When the washer breaks down, the laundry routine becomes completely disrupted, causing additional stress and difficulty. Since it is essential for Surrey residents to preserve the longevity and efficiency of their washing machines, here is the list of the most typical washer issues that can help identify and fix them quickly, keeping the appliance in excellent working condition.
Washer door or lid won’t lock
If your washer door or lid won’t lock, it may fail to start or finish its cycle. This problem typically results from faulty door lock mechanism or issues with the control board. As for the faulty lock mechanism it is usually easy to replace. If it is about the control board, professional repair is required to fix or replace it.
Washing machine door seal is broken
A damaged door seal might result in leaks and inefficient washing. It frequently happens due to the wear and tear or an improper use of the appliance. As the door seals may deteriorate over time, it is recommended to check the seal frequently for holes or cracks and replace it if needed. Besides, make sure the washer is not overloaded since this can put stress on the seal.
Error code on the washer panel
Modern washers display error codes to indicate specific problems. To identify these issues and determine if they require professional assistance or can be easily fixed without contacting the repair company, consult the washer’s manual.
Washer won’t start
There are several possible reasons why your washer won’t start. If it is about the problems with the power supply, make sure the outlet is working and the washer is plugged in. There also may be the case of a faulty start switch. If the start button does not engage, it may be necessary to replace the switch. Finally, a malfunctioning control board may prevent the washer from starting.
Washing machine door gasket mold
Mold growth in the door gasket is a common problem with front-loading washers. In order to resolve this issue, wipe the gasket dry after every usage, then use a washer cleaner to run a monthly cleaning cycle. Leaving the washer’s door slightly open in between usage to let some fresh air in may also help prevent the mold growth.
Washer fills slowly
It might be annoying when a washer takes a while to fill. It usually happens because of the clogged inlet filters or low water pressure. Clean the water inlet filters on a regular basis and make sure the water pressure in your house is appropriate.
Washing machine won’t fill with water
When the water in your washer refuses to fill, primarily verify that the water supply valves are fully open and if they turn out to be faulty, replace them.
Washer is overflowing
A clogged drainage hose or a malfunctioning water level switch are frequently the causes of the overflowing washers that can result in serious damage. This problem can be avoided by making sure the water level switch is not defective and the drain tube is free of obstructions.
Water level in the washer is low
If the water level in your washer is consistently low, verify that the water level setting you have chosen is correct. If it is about water level sensor malfunction, it may require replacement or recalibration.
Washer won’t spin
Your washing routine is disrupted when a washer fails to spin, leaving clothes soaking wet. Redistributing the clothing equally within the drum can address the potential cause of this issue, which often stems from an imbalanced load. If the issue does not go away, it can be caused by a malfunctioning drive belt or motor, which has to be inspected and potentially replaced.
Washer is making a loud noise
When your washer makes loud noises, it usually means that there are some loose objects in the drum or the bearings are worn-out and need replacing.
Burning smell from a washer
A burning smell coming from the washer is a reason to be worried since it can mean an overheating motor or any electrical issues. Immediately turn off the washer and examine the motor. A burning smell resulting from faulty wiring or components requires expert repair.
Washer stops mid cycle
If your washer stops mid-cycle, it is possible that the washer overheated. In this case, restart after letting it cool down. Another cause may be a malfunctioning timer or control board that requires examination and replacement.
Washer smells bad
Your washer’s unpleasant smells could be caused by mold and mildew or the poor drainage. Use a washer cleanser to get rid of buildup and clean the gasket and drum on a regular basis. Make sure the washer is draining properly to avoid stagnant water.
Washer fails to drain
Possible causes of a washer that won’t drain include clogged drain hose or faulty pump. Clear the hose of any obstructions. If the drain pump is malfunctioning, it has to be replaced.
Although they are an indispensable appliance, washing machines may certainly present a set of their own issues. You can improve your washer’s performance and increase its longevity by being aware of the typical problems that may occur and how to avoid bigger problems later on.
